Comparison Guide · Pier Systems
Helical piers vs push piers: two ways to reach stable soil
Kansas City pier proposals tend to lead with a pier type — helical or push — as if the type itself were the decision. It is part of the decision, but not the largest part. Both systems are typically quoted inside the same published range, $1,250–$2,500 per pier, and both aim past KC's expansive clay to stable strata below. What separates a sound proposal from a weak one is the scope it prices, the capacity it records, and the warranty behind it. This page compares the two systems directly, then shows how to compare two bids for either one.
Side by side
| Factor | Helical piers | Push piers (resistance piers) |
|---|---|---|
| How it works | A steel shaft with helical plates is rotated into the ground with a hydraulic drive motor, screwing down to load-bearing strata. A bracket at the top connects the shaft to the footing. | Smooth steel pier sections are driven with a hydraulic ram using the structure's weight as counter-pressure, adding sections until the pier reaches load-bearing strata or refusal. A bracket connects the pier to the footing. |
| Typical per-pier cost | $1,250–$2,500 per pier — within the published KC range | $1,250–$2,500 per pier — within the published KC range |
| Load capacity verification | Installation torque is measured as the pier advances; torque correlates with soil capacity and is recorded per pier. | Driving pressure at final depth is recorded; capacity is inferred from the pressure required to advance or hold the pier under load. |
| When each is often used | Lighter structures, additions, and situations where the house weight is limited or unavailable as driving resistance; also used where torque verification is preferred and where vibration should be minimized. | Heavier structures where the building weight is available to drive against; a long-established choice for residential settlement repair where depth to stable strata is the governing factor. |
| KC clay-soil notes | Helix size and shaft depth are selected to carry below the active clay zone. Torque readings help confirm the pier has passed through the shrink-swell layer into more consistent material. | Sections are added until driving resistance indicates the pier has passed the active clay zone. Final depth varies by lot — clay depth is not uniform across the metro. |
| Warranty differences | Terms are set by the installing company and the pier manufacturer, not by the pier type. Confirm coverage scope, transfer terms, exclusions, and backing for the specific helical system proposed. | Terms are set by the installing company and the pier manufacturer, not by the pier type. Confirm the same four points for the specific push pier system proposed, in writing. |
Per-pier ranges are planning estimates based on the $1,250–$2,500 range Kansas City companies typically publish, researched November 2026. They are not quotes, bids, or guaranteed prices. At those rates, partial piering typically runs ~$5,000–$15,000 and full piering ~$10,000–$35,000. For overall context, Angi's published Kansas City average across all foundation jobs is $5,569.
How to compare two pier bids
Two bids for the same house can differ by thousands of dollars while using the same pier type — or different pier types at nearly the same total. Compare them in this order, using the foundation repair cost guide as the pricing reference and the pier cost estimator to check totals against published rates.
| Compare this | What to look for |
|---|---|
| Scope first | Are both bids pricing the same walls and the same pier locations? A bid with fewer piers is not a lower price for the same job — it is a different job. An independent engineer's plan settles this. |
| Per-pier rate | Divide each piering subtotal by its pier count. Both answers should be interpretable against the $1,250–$2,500 published range. Ask for a written explanation of any rate well above it. |
| Depth & capacity records | Ask what will be recorded per pier — final depth and torque for helical piers, final depth and driving pressure for push piers — and whether you receive those records at completion. |
| Interior vs exterior | Interior piers add floor breakout and patching. Confirm whether that work, and any flooring restoration, is included or listed separately in each bid. |
| Lift expectations | Ask what lift, if any, is attempted, and what result is realistic for your house. Stabilization and full recovery of original elevation are different outcomes. |
| Warranty in writing | Coverage scope, transferability and transfer fee, exclusions, and who backs the warranty if the local office closes. Compare the written terms, not the summary given in person. |
The 30-second bid test
Set two bids side by side and find three numbers on each: pier count, piering subtotal, and the resulting per-pier rate. If the counts differ, you are comparing scopes, not prices — resolve the scope with an engineer's letter first. If the counts match and the rates differ, the rate gap, the capacity records, and the written warranty are the whole conversation.
What moves your price up or down
Keeps cost down
Partial scope on the settled wall only, as defined by an engineer · exterior placement with clear access (no floor breakout) · shallower depth to stable strata on your lot · comparing bids on the same scope so pier count reflects need, not presentation.
Pushes cost up
Full-perimeter scope with a higher pier count · interior piers through a finished floor · deeper piers to reach stable strata through thick clay · premium per-pier pricing above the published range · waterproofing or other work bundled into the piering ticket without separate line pricing.
Pier system questions, answered
What is the difference between helical piers and push piers?
A push pier is a smooth steel pier driven into the ground with a hydraulic ram, using the weight of the house itself as resistance, until it reaches load-bearing soil or refusal. A helical pier is a steel shaft with helical plates — like a large screw — that is rotated into the ground with a drive motor, and it does not need the weight of the house to install. Both transfer the foundation load to deeper, more stable strata; they reach that strata by different methods.
Do helical piers and push piers cost the same in Kansas City?
In published Kansas City pricing, both types are typically quoted inside the same $1,250–$2,500 per-pier range. Where a specific proposal lands in that range depends more on pier depth, access, interior vs exterior placement, and the company's pricing than on pier type alone. That is why comparing per-pier rates and pier counts on the same engineer-defined scope matters more than comparing pier-type labels.
Which pier type is better for Kansas City clay soil?
Kansas City's expansive clay is the reason both types are used here: each aims to bypass the active clay layer that swells and shrinks with moisture and reach more stable material below. Helical piers are often considered where the structure is lighter, where installation torque can be used to estimate capacity, or where the weight of the house is not available as driving resistance. Push piers are often considered for heavier structures where that weight is available. Soil conditions at your lot and the engineer's specification decide the fit — not a general preference.
How is pier load capacity verified?
For push piers, capacity is inferred from the hydraulic driving pressure reached at final depth and from the result of any lift attempt. For helical piers, installation torque is correlated with capacity — the torque required to advance the helix is a widely used indicator of the soil resistance the pier can mobilize. In both cases, ask what verification the installer records per pier, and whether those records are included in your project documentation.
Does pier type change the warranty?
Warranty terms vary more by company than by pier type. Read four points on any proposal, whichever pier is specified: whether the warranty covers the piers only or the movement they were meant to stop, whether it transfers to a new owner and at what fee, what conditions void it (plumbing leaks and drainage problems are common exclusions), and whether it is backed by the local office or a national organization. Get those terms in writing for the specific pier system being installed.
Have two pier bids that do not line up?
Run the estimator to check each total against published rates, then answer the 60-Second Brief. We'll match you with a vetted local pro who bids to an engineer's scope — free, no obligation.
Start the 60-Second Brief